cmos linear image sensor small, resin-sealed cmos image sensor www.hamamatsu.com s10227-10 1 barcode readers compact and high cost-performance surface mount type package: 4.4 9.1 1.6 t mm pixel pitch: 12.5 m pixel height: 250 m displacement meters refractometers interferometers miniature spectrometers 512 pixels single 5 v power supply operation spectral response range: 400 to 1000 nm video data rate: 5 mhz max. built-in timing generator allows operation with only start and clock pulse inputs. simultaneous charge integration shutter function high sensitivity, low dark current, low noise absolute maximum ratings structure parameter symbol condition value unit supply voltage vdd ta=25 c -0.3 to +6 v clock pulse voltage v(clk) ta=25 c -0.3 to +6 v start pulse voltage v(st) ta=25 c -0.3 to +6 v operating temperature * 1 topr -25 to +85 c storage temperature * 1 tstg -25 to +85 c re ow soldering conditions * 2 tsol peak temperature 260c, 3 times (see p.6) - * 1: no condensation * 2: jedec level 2a note: exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. always be sure to use the product within the absolute maximum ratings. parameter speci cation unit number of pixels 512 - pixel pitch 12.5 m pixel height 250 m photosensitive area length 6.4 mm package glass epoxy - seal material silicone resin - the s10227-10 is a resin-sealed cmos linear image sensor to offer compact size and high cost-performance compared to our previous product (s9227 series). features applications
cmos linear image sensor s10227-10 2 recommended terminal voltage electrical characteristics [ta=25 c, vdd=5 v, v(clk)=v(st)=5 v] electrical and optical characteristics [ta=25 c, vdd=5 v, v(clk)=v(st)=5 v, f(clk)=5 mhz] parameter symbol min. typ. max. unit supply voltage vdd 4.75 5 5.25 v clock pulse voltage high level v(clk) vdd - 0.25 vdd vdd + 0.25 v low level - 0 - v start pulse voltage high level v(st) vdd - 0.25 vdd vdd + 0.25 v low level - 0 - v parameter symbol min. typ. max. unit clock pulse frequency f(clk) 50 k - 5 m hz video data rate vr - f(clk) - hz current consumption i202632ma conversion ef ciency ce - 1.6 - v/e - parameter symbol min. typ. max. unit spectral response range 400 to 1000 nm peak sensitivity wavelength p - 700 - nm dark output voltage * 3 vd -110 mv saturation output voltage * 4 vsat 4 4.3 - v readout noise nr - 0.45 1 mv rms output offset voltage vo 0.4 0.6 0.9 v photoresponse nonuniformity * 5 * 6 prnu - - 8.5 % * 3: integration time=10 ms * 4: voltage difference from vo * 5: photoresponse nonuniformity (prnu) is the output nonuniformity that occurs when the entire photosensitive area is uniformly illuminated by light which is 50% of the saturation exposure level. prnu is measured using 510 pixels excluding the pixels at b oth ends, and is de ned as follows: prnu= ? x/x 100 (%) x: average output of 510 pixels excluding the pixels at both ends, ? x: difference between x and maximum or minimum output * 6: measured with a tungsten lamp of 2856 k spectral response (typical example) block diagram wavelength (nm) relative sensitivity (%) (ta=25 c) 400 500 600 700 900 800 1000 1100 1200 0 20 40 60 80 100 kmpdb0258ed timing generator shift register hold circuit charge amp array 1234 photodiode array 511 512 clk st gnd vdd eos video 8 1 4 6 5 7 kmpdb0167ec
cmos linear image sensor s10227-10 3 timing chart chart (s9227-03) kmpdc0166e clk st clk video tf(clk) tr(st) tf(st) tr(clk) tvd2 tvd1 tlp(st) thp(st) tpi(st) 1/f(clk) clk st video eos 512 tlp(st) thp(st) tpi(st) trigger 1/f(clk) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 14 clocks 100 ns 2.5 clocks 8.5 clocks integration time kmpdc0166ef parameter symbol min. typ. max. unit start pulse interval tpi(st) 530/f(clk) - 1100 m s start pulse high period thp(st) 8/f(clk) - 1000 m s start pulse low period tlp(st) 15/f(clk) - 100 m s start pulse rise and fall times tr(st), tf(st) 0 20 30 ns clock pulse duty - 45 50 55 % clock pulse rise and fall times tr(clk), tf(clk) 0 20 30 ns video delay time 1 tvd1 32 40 48 ns video delay time 2 tvd2 40 50 60 ns note: dark output increases if the start pulse period or the start pulse high period is lengthened. the internal timing circuit starts operating at the rise of clk pulse immediately after st pulse sets to low. the integration time equals the high period of st pulse plus 6 clk cycles. the output from 1st channel appears 14 clocks plus 100 ns after the falling edge of st pulse. the eos pulse is output 39 ns after the falling edge of clk pulse. the output voltage after reading the last pixel (512 ch) is inde nite. start pulse setting example (for setting the start pulse period to a minimum and the integration time to a maximum) start pulse high period=515/f(clk), start pulse low period=15/f(clk)
cmos linear image sensor s10227-10 4 dimensional outline (unit: mm) (0.9) 0.3 0.15 2.54 1.6 0.2 silicone resin photosensitive surface glass epoxy index mark 2.54 2.54 2.54 electrode (8 ) ?0.5 tolerance unless otherwise noted: 0.1 values in parentheses indicate reference value. 4.4 9.1 photosensitive area (6.4 0.25) 1 ch 3.2 1.35 0.2 512 ch 1.437 0.2 top bottom [top view] [side view] [bottom view] kmpda0316eb pin no. symbol i/o discription 1 gnd - ground 2 nc - no connection 3 nc - no connection 4 vdd i power supply voltage 5 video o video signal output 6 eos o end of scan 7 st i start pulse 8 clk i clock pulse pin connections
cmos linear image sensor s10227-10 5 recommended land pattern (unit: mm) 2.54 2.54 2.54 (8 ) ?0.7 2.54 kmpdc0257ea packing quantity 2000 pcs/reel packing type reel and desiccant in moisture-proof packing (vaccum-sealed) kmpdc0450ea 4.0 0.1 7.5 0.1 1.75 0.1 9.45 0.1 2.0 0.05 8.0 0.1 1.89 0.1 0.32 0.05 4.75 0.1 16.0 -0.1 +0.3 ?1.5 -0 +0.1 1 ch reel feed direction ?1.5 -0 +0.25 embossed tape (unit: mm, material: polycarbonate resin, conductive) standard packing speci cations reel (conforms to jeita et-7200) dimensions hub diameter tape width material electrostatic characteristic 330 mm 100 mm 16 mm ppe conductive appearance inspection standards parameter test criterion inspection method foreign matter on photosensitive area 10 m max. automated camera
cmos linear image sensor s10227-10 6 ? this product supports lead-free soldering. after unpacking, store it in an environment at a temperature of 30 c or less and a humidity of 60% or less, and perform soldering within 4 weeks. ? the effect that the product receives during re ow soldering varies depending on the circuit board and re ow oven that are used. before actual re ow soldering, check for any problems by tesitng out the re ow soldering methods in advance. ? when three or more months have passed or if the packing bag has not been stored in an environment described above, perform baking. for the baking method, see the related information ?resin sealed type cmos linear image sensor / precautions.? precautions (1) electrostatic countermeasures this device has a built-in protection circuit as a safeguar d against static electrical charges. however, to prevent destroying the device with electrostatic charges, take countermeasures such as grounding yourself, the workbench and tools. protect this device from surge voltages which might be caused by peripheral equipment. (2) package handling the photosensitive area of this device is sealed and protected by transparent resin. when compared to a glass faceplate, the su rface of transparent resin may be less uniform and is more likely to be scratched. be very careful when handling this device and also when designing the optical systems. dust or grime on the light input window might cause nonuniform sensitivity. to remove dust or grime, blow it off with compresse d air. (3) surface protective tape protective tape is af xed to the surface of this product to protect the photosensi tive area. after assembling the product, remove the tape before use. (4) operating and storage environments handle the device within the temperature range speci ed in the absolute maximum ratings. operating or storing the device at an ex- cessively high temperature and humidity may cause variations in performance characteristics and must be avoided. (5) uv exposure this product is not designed to prevent deterioration of characteristics caused by uv exposure, so do not expose it to uv light . recommended temperature pro le for re ow soldering (typical example) time 300 c preheating 60 to 120 s soldering 60 to 150 s peak temperature 260 c max. 217 c 200 c 150 c peak temperature - 5 c 30 s max. 25 c to peak temperature 8 m max. heating 3 c/s max. cooling 6 c/s max. temperature kmpdb0405ea
cat. no. kmpd1152e03 mar. 2015 dn www.hamamatsu.com hamamatsu photonics k.k., solid state division 1126-1 ichino-cho, higashi-ku, hamamatsu city, 435-8558 japan, telephone: (81) 53-434-3311, fax: (81) 53-434-5184 u.s.a.: hamamatsu corporation: 360 foothill road, bridgewater, n.j. 08807, u.s.a., telephone: (1) 908-231-0960, fax: (1) 908-23 1-1218 germany: hamamatsu photonics deutschland gmbh: arzbergerstr. 10, d-82211 herrsching am ammersee, germany, telephone: (49) 8152- 375-0, fax: (49) 8152-265-8 france: hamamatsu photonics france s.a.r.l.: 19, rue du saule trapu, parc du moulin de massy, 91882 massy cedex, france, teleph one: 33-(1) 69 53 71 00, fax: 33-(1) 69 53 71 10 united kingdom: hamamatsu photonics uk limited: 2 howard court, 10 tewin road, welwyn garden city, hertfordshire al7 1bw, unit ed kingdom, telephone: (44) 1707-294888, fax: (44) 1707-325777 north europe: hamamatsu photonics norden ab: torshamnsgatan 35 16440 kista, sweden, telephone: (46) 8-509-031-00, fax: (46) 8-5 09-031-01 italy: hamamatsu photonics italia s.r.l.: strada della moia, 1 int. 6, 20020 arese (milano), italy, telephone: (39) 02-93581733 , fax: (39) 02-93581741 china: hamamatsu photonics (china) co., ltd.: b1201, jiaming center, no.27 dongsanhuan beilu, chaoyang district, beijing 100020 , china, telephone: (86) 10-6586-6006, fax: (86) 10-6586-2866 product specifications are subject to change without prior notice due to improvements or other reasons. this document has been carefully prepared and the information contained is believed to be accurate. in rare cases, however, there may be inaccuracies such as text errors. before using these products, always contact us for the delivery specification sheet to check the latest specifications. the product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovere d and reported to us within that one year period. however, even if within the warranty period we accept absolutely no liability for any loss caused by natural d isasters or improper product use. copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. information described in this material is current as of march 2015. cmos linear image sensor s10227-10 7 related information precautions ? disclaimer ? image sensor / precautions ? resin-sealed cmos linear image sensors / precautions www.hamamatsu.com/sp/ssd/doc_en.html
|
